 Torque wrenches deliver the power and accuracy required to tighten nuts and bolts while preventing structural damage. These tools ensure that connections are tightened according to engineering specifications and prevent loosening while a structure or piece of equipment is in use. Torque wrenches also prevent over-tightening, which can damage threads, shorten the lifespan of a connection or cause sudden structural failure.
When choosing industrial torque wrenches and multipliers, you’ll need to consider project specifications, maneuverability and available or preferred power source. It’s important to remember that your initial purchase or rental is not only about procuring the product — it’s about the subsequent service. Every torque tool requires yearly calibration, so make sure the supplier you’re considering can provide annual calibration services, certificates and necessary repairs. Read on for what to consider when selecting a torque wrench for your application and some important safety reminders. Types of Industrial Torque Wrenches High-capacity torque wrenches can either be hydraulic, manual, electric, battery-powered, or pneumatic. Torque wrenches can be categorized further depending on their design and intended application. Manual (Click-Type) Torque Wrench These hand-operated tools can be set to deliver a specific amount of torque and will “click” once the desired torque has been reached. Click-type torque wrenches are best for jobs in tight spaces or with low visibility, since the wrench will give an audible cue once it achieves the preset torque. These tools have long lifespans, few parts or accessories and are fairly simple to use. Torque Multiplier For bolts that require a high amount of torque (or have been over-tightened), torque multipliers can deliver additional torque without requiring extra force on the part of the operator. Torque multipliers are essential for maintaining worker safety while tightening or loosening bolts by hand. Multipliers can also increase torque at small intervals at a very slow pace, reducing the risk of over-torquing or worker injury. Electric Torque Wrench With the ability to deliver more precise accuracy than an analogue tool, corded or battery-powered electric torque wrenches can be preset to a desired torque within ±3% to ±5% repeatable accuracy. If you choose to go untethered with a battery-powered torque wrench, have extra batteries or a charger on hand. If corded electric torque wrenches are your preference, be sure there is adequate clean power that allows you to safely reach your work area. This includes the proper generators (no welding generators or boom lifts) and/or properly installed spider boxes that output the correct power for the tools. If extension cords are necessary, anything longer than 150 ft. is not recommended. Hydraulic Torque Wrench When it comes to larger jobs, hydraulic torque wrenches are able to deliver over 25,000 ft.-lbs. of torque. They come in square-drive or low-profile designs called cassettes, which consist of the cassette and drive unit. Hydraulic wrenches themselves are quite light, but are accompanied by heavy systems that can carry a high price tag. Hydraulic systems include pumps and a stiff hose that can be difficult to move. Hydraulic torque wrenches also carry safety concerns related to pinch hazards and hydraulic fluid leaks, and should only be used by trained operators. Pneumatic Torque Wrench Like hydraulic tools, pneumatic torque wrenches can deliver much higher torque than a manual or electric wrench, but require additional equipment like an air hose and compressor. Torque Wrench Considerations The type and model of torque wrench you choose depends on your specific use case. Some considerations are fairly straightforward — torque range, size, power source — while some are often overlooked during the buying or rental process. Here is a list of questions to consider while making your torque tool selection:
Torque Wrench Safety Tips Be sure that all operators are briefed on safe handling and precautions before using any high-capacity torque tools. Here are some general safety guidelines to keep in mind:
Read the full article from GWY here. This Safety Flash was contributed by Don Laro, Sales and Marketing Manager for GWY, in cooperation with SEAA’s Safety & Education Committee. It’s designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations. Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected]. The 10th Annual National Safety Stand-Down to Prevent Falls in Construction will take place May 1-5, 2023. This initiative from OSHA helps to raise awareness on fall hazards in an effort to reduce fall fatalities and injuries. In 2021, there were 17 fatalities in the structural steel and precast concrete contractors’ sector and 11 of them were due to a fall, slip or trip, according to data from the Bureau of Labor Statistics.
“In the first three quarters of FY 2022, OSHA conducted over 9,700 inspections in the construction industry, of which 47% identified fall hazards with over $34 million in penalties issued for serious and willful violations in fall protection,” said Patrick Kapust, deputy director of OSHA’s Directorate of Enforcement Programs said in an interview about OSHA’s 2022 Top 10 Citations list. The list shows that OSHA cited 5,260 violations for Fall Protection-General Requirements in 2022, making it the number one most frequently cited workplace safety standard for the 12th year in a row. Fall Protection- Training Requirements also made the list as number eight. Four of the top ten citations are related to working as height which is why OSHA encourages employers to participate in the initiative by hold Safety Stand Down meetings the first week of May. Companies can conduct a Safety Stand-Down by taking a break to have a toolbox talk or another safety activity like conducting safety equipment inspections, developing rescue plans, or discussing job specific hazards. It can also be an opportunity for employees to talk to management about falls and other job hazards they see. In support of the National Safety Stand-Down, SEAA has created a Safety Stand Down page with lots of resources. Our downloadable posters are available for free to the public. The new poster for the 2023 Safety Stand Down, How to Make JSA’s Intentional, provides suggestions on how to complete a job safety analysis and getting the whole team involved in order to keep safety at the forefront of the job. Additional resources provide insight into related topics, such as fall prevention for loading and unloading trailers, wind hazards on elevated work platforms, protecting retractable lifelines from arcing damage, and more. Visit the Safety Stand Down Resources page for best practices. Resources: Census of Fatal Occupation Injuries Summary, 2021 OSHA’s Top 10 Citations of 2022 Injuries, Illnesses, and Fatalities, 2021. NAISC code 23812 This Safety Flash was contributed in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations. Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected]. ANSI Z359.14-2021: What You Should Know to Comply with the Updated Self-Retracting Devices Standard2/13/2023
What are the high-level changes that ANSI Z359.14-2021 addresses? On June 17, 2021, ANSI approved the new 2021 revision of Z359.14, Safety Requirements for Self-Retracting Devices (SRDs) for Personal Fall Arrest and Rescue Systems. This revision supersedes the 2014 version and goes into effect on August 1, 2023, which is an important date for ANSI compliance while using self-retracting devices. In the previous 2014 revision of Z359.14, SRDs were organized by type (SRL, SRL-R for devices with rescue/retrieval functions, or SRL-LE for leading edge capability) and class (Class A or Class B). The intent was to organize SRDs by features in "Type" and then by their overhead performance capability by "Class." At a high level, the 2021 changes to the ANSI Z359.14 standard are designed to:
What will be the new ANSI Z359.14-2021 SRD types and classes? Both types and classes were overhauled in 2021: "types" are SRL, SRL-P for personal devices meant to be installed on the user's full body harness, or SRL-R for devices with rescue/retrieval functions, and "classes" are Class 1 or Class 2. The SRD class is now applied to acceptable anchorage locations. Class 1 devices are suitable for at or above dorsal D-ring anchorage locations. Class 2 devices are suitable for above, at, or up to 5 feet below the dorsal D-ring anchorage locations AND must be leading edge rated. So, if your jobsite has edge exposures and you need a leading edge SRL or SRL-LE, you will be looking for a Class 2 device in compliance with ANSI/ASSP Z359.14-2021.  With the type and class changes, Z359.14-2021 also introduced standard overhead performance criteria for all SRDs and standardized class labeling. Now, a worker will be able to quickly identify the suitable device for the hazards faced in their work zone. In the 2012 and 2014 revisions of Z359.14, overhead performance criteria were defined by SRD class: Class A or Class B. In 2021, overhead performance will be standardized across all SRDs. The performance requirements are summarized in the table below:  What is the new ANSI Z359.14-2021 standardized labeling requirements? All ANSI/ASSP Z359.14-2021 compliant SRDs will have one of the markings below consistent with its class:   In addition to the Class 1 and Class 2 standard labels, all Class 2 SRLs must include a full fall clearance table or diagram as part of the physical product and the user instruction manual. This provides critical clearance information directly on the product, where it is most easily accessible by the end user or Competent Person at the place and time of use. How will the testing of SRDs change with the new ANSI Z359.14-2021 requirements? The 2021 version of Z359.14 significantly expands the volume and severity of testing required to comply with the standard. Most of these changes are intended to improve safety factors and address specific known hazards or applications of SRDs. While testing the products mainly affects manufacturers and test labs, it's essential to understand how these changes may impact how these devices are deployed and used in the field by end users. Some of the significant changes include:
What is the compliance timeline for existing SRDs in use? ANSI/ASSP Z359.14-2021 goes into effect on August 1, 2023. For organizations or job sites that mandate ANSI compliance, all SRDs must be manufactured and marked as compliant with Z359.14-2021. Any SRDs marked as compliant with Z359.14-2014 or any previous revision will be considered out of compliance after August 1, 2023. FallTech recommends reaching out to your manufacturer to inquire how this standard change affects the SRDs that you are using now and plan your transition to 2021 compliant devices. I currently use a non-Leading Edge rated personal device in a below D-ring application. Will this still be allowed after August 1, 2023? This question has a two-part answer that depends on the ANSI compliance requirements of your organization or worksite. If strict ANSI compliance is required, then after August 1, 2023, only a Class 2 SRL-P will be appropriate for this application. If only OSHA compliance is mandated, then the existing device may continue to be used as approved by your Competent Person, Qualified Person, and/or Professional Engineer. You should use a five-foot set-back distance versus an anchorage at the leading edge because it equips your fall protection system to arrest the fall more quickly. If your anchorage is at the edge, the SRL will create additional freefall distance as it retracts. The pawl mechanism also needs the lifeline to pay out fast enough to engage. With a zero-foot set-back distance and below D-ring foot-level tie-off, it won’t activate until the worker has fallen below the device hanging beneath the leading edge, further delaying the arrest. With a five-foot set-back distance, this payout begins as soon as the user’s D-ring passes below the level of the anchorage. You can eliminate the extra freefall length, lower the MRFC, and create a safer working environment. Read the full article on FallTech's Safety Blog. This Safety Flash was contributed by FallTech, in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations.
Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected].  Mobile elevating work platforms (MEWPs) are indispensable tools when it comes to allowing workers to work safely at height. However, there are specific hazards associated with their operation that operators must be aware of. These hazards have been identified by the manufacturers, can be found in the operator's manual for each model, and are to be observed in conjunction with all other workplace safety rules and regulations.
One of the hazards that operators must always be on the alert for is windy conditions. Per ANSI1, outdoor-rated MEWPs must be designed to be stable in winds up to 28 mph if all other factors are taken into consideration, which I will discuss further in a moment. Any wind above 28 mph will place the machine, and the occupants, in serious jeopardy. One unfortunate example of that is described on the OSHA Scissor Lift Fact Sheet 2: “Caution: Wind Can Make Extended Scissor Lifts Unstable. During the Fall 2010 college football season, a student who was also an employee of the University of Notre Dame was killed while filming the school’s football team practice from a scissor lift. Reportedly, the untrained worker raised the lift over 39 feet to film the practice. The wind gusts that day were more than 50 miles per hour. The high winds blew the lift over, killing the worker.” Please note that this example from the OSHA Scissor Lift Fact Sheet stresses that the individual was untrained. One comment that I often hear from untrained operators is, “I thought it would be safe or it wouldn’t let me go up.” The fact is that MEWPs are only machines, and even with all the safety devices that are designed into them, they are only truly safe in the hands of well trained, well supervised operators. Best Practices In the latest round of ANSI A92 design standards3, there are provisions for both outdoor rated and indoor-only rated machines. Indoor-only machines can only be used in areas that are not exposed to any wind whatsoever. This even includes warehouses or other structures with open bay doors. All MEWPs that were manufactured to the previous standards are unaffected by that change. However, it is important to note that some manufacturers released indoor-only machines before the standards changed, so it’s important to be aware of the limitations on the MEWP being used. Indoor-only MEWPs must be clearly marked to that effect in a durable manner in an easily visible place. Many new scissor lifts provide an option to switch between indoor and outdoor modes. Operators should never use a machine in indoor mode while working outside, or in areas where the air is moving (such as around large shop fans). When using outdoor-rated MEWPs, in outdoor mode, the best rule of thumb is if you are not comfortable with the situation, don’t go up. If you are elevated and wind speeds do exceed 28 mph, immediately lower the MEWP and do not continue to operate the machine. There are tools that can be used to estimate wind speed, such as the Beaufort Wind Chart4, and if you are unsure, small handheld wind meters (anemometers) are available online for less than $30. There are other factors concerning wind that need to be taken into consideration as well. The combined weight of the occupants, materials, tools, and any options or accessories must never exceed the rated platform capacity of the MEWP. Care must be taken when handling building materials, sheet materials, panels and other such materials that can act as sails. No modifications or additions to the MEWP that affect its wind loading — and consequently its stability — should be made without the manufacturer’s approval. Certain manufacturer-approved options and accessories, such as panel cradles and material holders (when installed) can impose a reduced maximum wind speed rating. The shielding and funneling effects of certain structures can cause high wind speeds and turbulence on days when the wind speed in open areas is low, so caution should always be taken when working between buildings, in alleyways or other confined spaces. Other potential sources of local high wind speed that must be taken into considered in relation to safety at worksites are at airports and along roadways. 1ANSI A92.20-2021.4.2.2.4.1.1 2 Working Safely with Scissor Lifts 3 ANSI A92.20-2021.6.4.7 4 Beaufort Wind Chart — Estimating Wind Speeds This Safety Flash was contributed by Scott Owyen, Genie Director of Training in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations. Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected].  Did you know that hand and arm injuries are the most frequent and preventable injury in the workplace, accounting for more than 23 percent of injuries, according to an article by Safety + Health magazine?
On that same note, an article from Occupational Health & Safety magazine reported that more than one million workers are sent to the emergency room each year due to serious hand, arm, and finger injuries. Training, communication, and planning are often all that’s needed to reduce risk of pinch points on the job. On a recent reinforcing steel project, the task was to adjust a pier cap filled with #11 bar. Shelby Erectors, a reinforcing steel and metal decking and member of SEAA, experienced a minor incident where an employee pinched his arm when the pier cap shifted. Here is what we discovered when we reviewed the incident. The pinch point risk was identified and addressed in the daily pre-task meeting, however, the injured employee showed up late and did not go through the original pre-task meeting. The foreman allowed the worker to get right to work rather than reviewing the pre-task information with him individually. Although the hurt employee was trying to do the right thing by jumping to work after being late, he was not fully aware of how the task was being approached to avoid risk. This resulted in the employee putting his arm in an area that was not fully protected. Training on identifying pinch points and proper planning to avoid the hazard are key to incident prevention. What are potential pinch points? These examples are just a few of the possible pinch points Shelby Erectors comes across in the course of typical work days.
Best Practices to avoid pinch points:
And finally:
Resources: Occupational Health & Safety: Understanding Hand Injuries in the Workplace Safety + Health: Hand Safety Programs OSHA Cranes & Derricks in Construction 1926.1430(e) Michigan Occupational Safety and Health Act, Fact Sheet on Pinch Points Bureau of Labor Statistics, Employer-Reported Workplace Injuries and Illnesses Report 2020 This Safety Flash was contributed by Jason Zyla, Safety Manager, Shelby Erectors, in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations. Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected].  Falls in construction are the leading cause of deaths in the United States. OSHA states that employers are responsible for putting preventative measures in place to protect employees from falls at height, which includes having a fall protection plan. But what exactly does a fall protection plan entail? Let’s explore! The main purpose of the plan is to determine the fall hazards at the worksite and establish the methods and equipment each company will use to protect its workforce. Most jobsites and many state or local regulations even require contractors to have a plan on record. Not only is it important to have a plan, but employers also need to ensure its workforce understands the plan. Workers should also be trained on implementing the plan and what to do in case of a fall. Accidents happen, but with a good fall protection plan in place it can help reduce the chance of serious or fatal injuries.
Jobsite Info
It’s important to include jobsite information in your plan. This will consist of general information about the project; company name, the pre-identified competent person, jobsite address, and scope of work. Also make sure to include phone numbers for first responders in the event of an emergency. Make sure to identify the fall hazards on site. Do this prior to starting work and remember that no two jobs are the same. Evaluate all of the potential hazards on the project and ensure that you understand how the work is to be completed. Make note of where will employees be working, and the known fall hazards. Including, leading edge work, floor holes, connecting operations, ladders, and use of mobile elevating work platforms (MEWPs), such as boom lifts or scissor lifts. Types of Equipment and Inspections There are many options for a fall protection system. Determine the equipment and methods prior to beginning work. When deciding the method of protection, you should use the hierarchy of controls. These controls (from most preferred to least) are as follows - Elimination, Passive Fall Protection, Fall Restraint, Fall Arrest, Administrative Controls.
Next, outline proper equipment assembly and installation requirements. Include inspection criteria as well as proper storage of equipment. Employees need to fully understand how the equipment works, the frequency of inspections that will be required, and what to do with equipment if they identify any damaged or defective equipment. Additionally, improper storage of equipment can cause premature damage or deterioration. Be sure to refer to manufacturer manuals and inspection criteria. Falling Objects The plan should also include best practices for protecting workers from falling objects. This can include controlled or limited access zones. If this route is taken, ensure the proper tape, signage and spotters are in position. Rescues In the event of a fall, time is critical and having a rescue plan is essential to minimize any potential injury. Ensure the workforce is aware of the plan and has been properly trained on the equipment and its location. In your fall protection plan, identifying a method of communication (via phone, radio, etc.) is key in the event of an emergency. Then, outline the rescue plan by type. Did the employee fall off of a ladder, MEWP, ascent or descent device, or scaffold? Make sure there is a rescue plan for each one. Founding father, inventor, and publisher Benjamin Franklin is credited with the saying: “If you fail to plan, you are planning to fail!” In safety, if you do not have a plan then you can almost guarantee you will fail. Every project is different and presents a unique set of challenges when setting up your Fall Protection Plan but following these steps should help make planning easier. Resources: OSHA Fall Protection Plan OSHA Fall Protection Page USACE Fall Protection Guide 3M Fall Protection Rescue Plan This Safety Flash was contributed by Dax Biederman, Senior Safety Consultant, Trivent Safety Consulting, in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations. Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected] At times we can get so focused on protecting ourselves on the jobsite that we forget about the risks the public could potentially be exposed to if they are near a jobsite. These risks include dropping a bolt onto a busy sidewalk from a high-rise structure in an urban environment, a 300-foot lattice boom lifting or lowering near public areas a block away, or torch cutting and welding on an existing office building full of people who don’t even know you are there. These are all real-life scenarios and challenges we face every day, but which can catch the public by surprise. Here are three ways to reduce risk to the public.
 Physical Barriers One way to keep the public safe is by preventing them from passing by or through a construction site. Setting up “hard barricade” boundaries is the best way to keep unauthorized people out of danger. Signs should be posted on these boundaries warning people not to enter the construction area. When arc welding, use shields made of noncombustible or flameproof material to protect everyone in the vicinity from direct rays of the arc. [29 CFR 1926.351(e)]  Dropped Object Prevention When it comes to steel erection, usually a simple fence on the ground isn’t enough protection. Dropped objects accounted for over 240 deaths in 2019, according to the Bureau of Labor Statistics. The goal is to prevent falling objects in the first place. The use of tool lanyards and catch nets are the best ways we can protect the public from dropped objects. When guard rails are used, they must have sufficient toe boards at least 3½ inches in height from top edge to floor level, and no more than a ¼ inch gap at the bottom. It must be capable of withstanding a force of 50 pounds applied in any direction. It’s always best practice to add mesh fencing from the top guard rail to the toe board for extra dropped object protection. Preventing Exposure to Equipment Another issue that affects public safety is exposure to equipment. This includes the operation of cranes, forklifts, aerial lifts, or other vehicles that could get caught between and struck by hazards. First, properly maintained equipment is far less likely to experience a failure. Thorough inspections by an authorized person is critical to the maintenance process. Any safety issues must be reported immediately and the equipment should be taken out of service until it is fixed by a qualified person. Next, use spotters! Spotters should always be used when the operator’s line of sight is interrupted. How many spotters should you use when operating equipment in a high-risk area? As many as it takes! Spotters tend to put themselves in a caught between/ struck by hazard situation. The spotter should always place him/herself in a position that has a clear line of sight with the operator and direction of travel while using good body positioning.
What It All Comes Down To The most effective way to keep the public safe starts with in depth planning, detailed pre-construction meetings, and keeping our employees’ training up to date. Employees need to have a clear understanding of the hierarchy and be made aware of the procedures, materials, tools, and equipment available to them to support their efforts in creating a safer job site for the public and other workers. Great safety cultures have foundations built from both directions, top down and bottom up all connecting in a common goal. Resources: Guidelines for Establishing the Components of a Site-specific Erection Plan Protection of Pedestrians (ICC) Section 3306 Dropped Object Prevention This Safety Flash was contributed by Austin Reiner, Safety Manager, Derr & Gruenewald Construction Company, in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations.
Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected].  The Roman philosopher Seneca once said, “Luck is what happens when preparation meets opportunity.” When companies approach compliance preparedness with this thought process, they are overwhelmingly successful in their interactions with OSHA.
Here are three tips to not only survive but thrive when OSHA visits your site.
Get more details about implementing these three tips and additional details. 1. Define who is your competent person onsite for hazardous activities. When an OSHA compliance safety and health officer arrives onsite for a scheduled visit, employee complaint or accident, they will want to know who the company’s competent person for those hazardous activities is. An OSHA "competent person" is defined as "one who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them" [29 CFR 1926.32(f)]. The two key words to this definition are “capable” and “authorization.” Companies will be able to demonstrate capability by the training the employee has had and work history. Authorization is demonstrated by companies defining who these competent persons are during the preconstruction process. 2. Provide formal and ongoing training for employees on hazardous activities. OSHA will request employee training records for hazardous activities during an investigation. Companies will be well served to provide formal training for all employees prior to putting them to work. For Steel Erectors, the must have training prior to starting work will probably involve:
3. Train employees on what to expect from OSHA visits and their rights under the law. When employees know what to expect they will be less apt to make compounding mistakes when dealing with OSHA. The rights of workers during an inspection are:
A full list of workers’ rights published by OSHA can be found here. While this list doesn’t encompass everything a company needs to do to prepare for an OSHA visit, by being proactive on the front end of projects, companies will save time, money, and their reputation if OSHA ever does visit. Resources: OSHA Worker Rights and Protections Worker Rights Under the Occupational Safety and Health Act of 1970 OSHA Workers Rights Pamphlet 1960.26 - Conduct of inspections This Safety Flash was contributed by Bryan McClure, Senior Safety Consultant, Trivent Safety Consulting, in cooperation with SEAA’s Safety Committee. It is designed to keep members informed about ongoing safety issues and to provide suggestions for reducing risk. Best practices are gathered from a variety of sources. They may be more or less stringent than individual corporate policies and are not intended to be an official recommendation from SEAA. Always get approval and direction from your company officers on any new practice or procedure as these best practices may not work for all situations. Everyone benefits when a worker avoids injury. Submit your ideas for Safety Flash to [email protected] |
RSS Feed
